Heated roll-to-roll calendering with controlled gap and force
- Compression force up to 150 kN
- Roller gap from 0 to 4 mm
- Roll heating up to 150 °C

In addition to that...
- Hydraulic gap setting with mechanical wedge adjustment
- Integrated bending compensation
- Both rollers servo-driven and synchronized
- Software-based speed ratio control between rollers
- Electric roll heating
- Speed range from 0.01 to 5.0 m/min
- Hardened steel rollers, 200 mm in diameter
- 75 mm pneumatic expanding mandrels
System overview
The FOM Calendering system 350 is a roll-to-roll calender that compacts coated and dried films between two heated rollers. Hydraulic pressure with mechanical wedge adjustment sets the roller gap from 0 to 4 mm, and an integrated bending compensation system counteracts roller deflection under load across the 360 mm roller length.
Both rollers are servo-driven and synchronized, and the speed ratio between them is set in software. Line speed runs from 0.01 to 5.0 m/min, and electric heating takes the rollers up to 150 °C.
Specifications
| Format | Roll-to-roll |
| Roller length | 360 mm |
| Roller diameter | 200 mm |
| Roller material | Hardened high-alloy steel |
| Compression force | Up to 150 kN |
| Roller gap | 0–4 mm |
| Gap adjustment | Hydraulic pressure with mechanical wedge |
| Roll heating | Electric, up to 150 °C |
| Drive | Servo-driven, both rollers synchronized |
| Speed | 0.01–5.0 m/min |
| Substrate rolls | Up to 350 mm outer diameter and 70 kg |
| Dimensions (H × W × L) | 1,900 × 1,100 × 1,780 mm |
| Weight | 1,100 kg |
Precise control of gap, force and temperature
Gap and force under control
Hydraulic pressure with mechanical wedge adjustment sets the roller gap from 0 to 4 mm, with up to 150 kN of compression force between the rollers. Integrated bending compensation counteracts roller deflection under load, across the full 360 mm roller length.
Heated rollers up to 150 °C
Electric heating takes the rollers up to 150 °C, so films can be calendered at elevated temperature or with heating switched off. The heat stays local to the rollers and does not affect the ambient conditions the system needs.
Synchronized servo drive
Both rollers are servo-driven and synchronized. Software-based motion control sets the speed ratio between the rollers, at line speeds from 0.01 to 5.0 m/min.
Roll handling and connections
Substrate rolls up to 350 mm in outer diameter and 70 kg mount on 75 mm pneumatic expanding mandrels. The system connects to a three-phase power supply, compressed air at 5–7 bar and Ethernet.

Every coating project starts with a material and a substrate. Tell us about yours and our coating experts will work through the process with you — from first trials in the lab to a route toward roll-to-roll.
Let our coating experts guide you
Frequently asked questions
What is the FOM Calendering system 350 used for?
The FOM Calendering system 350 is a roll-to-roll calender. It compresses a coated and dried film between two heated rollers to reduce its thickness and increase its density, at line speeds from 0.01 to 5.0 m/min.
What compression force and roller gap does the FOM Calendering system 350 provide?
The FOM Calendering system 350 applies a compression force of up to 150 kN between the rollers. The roller gap is set from 0 to 4 mm by hydraulic pressure with mechanical wedge adjustment, and an integrated bending compensation system counteracts roller deflection under load.
How hot can the rollers on the FOM Calendering system 350 get?
Electric roll heating takes the rollers up to 150 °C. This temperature is local to the rollers and does not change the permitted ambient temperature of the room, which is 5–25 °C.
How are the rollers on the FOM Calendering system 350 driven?
The standard configuration measures 680 × 895 × 1570 mm (H × W × L) and weighs 265 kg. It requires a 3-phase 400 V supply at 50/60 Hz with a maximum current of 24 A, compressed air at 5–7 bar (clean, dry, non-lubricated, ISO 8573-1:2010 Class 1.2.3 or better) via a Ø6 mm push-fit connection, and an Ethernet connection over RJ45.
What size substrate rolls does the FOM Calendering system 350 accept?
The FOM Calendering system 350 accepts substrate rolls up to 350 mm in outer diameter and 70 kg, mounted on 75 mm pneumatic expanding mandrels. The calender rollers are 360 mm long and 200 mm in diameter.
What does the FOM Calendering system 350 need to be installed?
The FOM Calendering system 350 requires a three-phase power supply (3P + N + PE, 3 × 200–480 V AC, 50/60 Hz, 17.7 A nominal current), compressed air at 5–7 bar, and an Ethernet connection via RJ45. The compressed air must be clean, dry and non-lubricated, to ISO 8573-1:2010 Class 1.2.3 or better. The system operates indoors in a clean, dry, non-corrosive environment at 5–25 °C and 20–60% relative humidity, non-condensing. It measures 1,900 × 1,100 × 1,780 mm (H × W × L) and weighs 1,100 kg.